ChaptersCapítulos
The ways back
FAÍSCA is not released yet. When it is, it will run on fm1-base, an open platform for the FM-1 that keeps several ways back to a working unit. They are listed here from the mildest to the strongest: try them in this order.
Before any install: back up your projects, sounds and samples with the official workbench, and keep the backup files. Use Chrome or Edge on a computer and a USB cable that carries data, not only charge. Keep the unit powered while anything is being written.
01Back to the official firmware
For a unit that starts. Open the official FM-1 workbench in Chrome or Edge, connect the FM-1, switched on, allow MIDI access when the browser asks, and install the official firmware. The workbench can return a unit to the original firmware and migrate it from compatible third-party firmware (a forced install, with its own confirmation). Then restore your backup.
| Official firmware | M-VAVE's download centre, under FM-1: the firmware and its release notes. |
| Official workbench | open.m-vave.com/fm1-workbench: update, return to the original firmware, back up and restore. |
| FM1 Open | The maker's open edition: source and SDK and releases. |
Switching firmware does not make projects and samples of one firmware readable by another: keep the backups made under the official firmware to restore under it.
02Safe mode
For a firmware that does not start. A firmware built on fm1-base that fails to start twice in a row starts the unit in SAFE MODE: there is no sound, but USB works, so a web installer can still reach the unit.
- Switch the unit off and on again; after two failed starts it shows safe mode.
- Press PLAY to try starting the firmware again.
- Or connect it and, from the installer, install the firmware again or put the official firmware back.
If safe mode itself fails twice, the unit falls back to the chip's own update mode (04).
03The bootloader's recovery menu
Where present. The fm1-base installer can also install m-bootloader (MIT), a small bootloader with a recovery menu. On a unit that has it, hold PLAY while switching the unit on to open the menu; from there a firmware package can be installed over MIDI even when the firmware will not start. Hold REC while switching on to put the unit in update mode, which the installer can reach.
04The chip's update mode
For a unit stuck in a crash loop, without m-bootloader. Holding REC at power-on then starts the chip's own update
mode, which an ordinary installer cannot reach. The rescue script in felucca-bsp
(tools/fm1_rescue.sh, macOS and Linux, MPL-2.0) puts the official firmware back through that mode with no
extra hardware: it checks the official firmware files against their known hashes and writes only those. Follow the
script's own instructions.
05A unit that shows nothing
For a unit with a dark screen that does not appear over USB at all. m-unbricker (MIT) recovers it with a second, working unit and a USB-C cable. In outline; its step-by-step page gives the details:
- Have a second unit that works and that m-unbricker supports. Nothing is installed on it: the recovery program runs from its memory, and its own firmware and settings stay.
- Open the step-by-step page in Chrome or Edge on a computer, connect the working unit by USB and allow MIDI access when the browser asks. The page starts the recovery program on the working unit.
- The working unit's screen then guides you: move the USB-C cable to the broken unit and switch it on. The working unit puts the broken unit's chip into its download mode and repairs it, whatever is in its memory.
- Then install the official firmware (01), if it is not already back, and restore your backup.
06Credits
m-unbricker and m-bootloader are by Julius Vitkauskas (MIT). fm1-base is by Charles Vestal and its contributors (MPL-2.0), built on felucca-bsp by Leo Kuroshita, Hügelton Instruments (MPL-2.0); the rescue script is Charles Vestal's, in felucca-bsp. The official firmware, the workbench and FM1 Open are M-VAVE's. None of them made, reviewed or endorse FAÍSCA. Every step on this page is at your own risk: see the legal page.
Os caminhos de volta
O FAÍSCA ainda não foi lançado. Quando for, ele vai rodar sobre o fm1-base, uma plataforma aberta para o FM-1 que guarda vários caminhos de volta a uma unidade funcionando. Eles estão aqui do mais leve ao mais forte: tente nesta ordem.
Antes de qualquer instalação: faça o backup dos projetos, sons e samples pelo workbench oficial e guarde os arquivos. Use Chrome ou Edge num computador e um cabo USB que passe dados, não só carga. Mantenha a unidade ligada enquanto algo estiver sendo gravado.
01Voltar ao firmware oficial
Para uma unidade que liga. Abra o workbench oficial do FM-1 no Chrome ou no Edge, conecte o FM-1, ligado, permita o acesso MIDI quando o navegador pedir e instale o firmware oficial. O workbench consegue voltar uma unidade ao firmware original e migrá-la de um firmware de terceiros compatível (uma instalação forçada, com confirmação própria). Depois, restaure o backup.
| Firmware oficial | Central de downloads da M-VAVE, em FM-1: o firmware e as notas da versão. |
| Workbench oficial | open.m-vave.com/fm1-workbench: atualizar, voltar ao firmware original, fazer e restaurar backup. |
| FM1 Open | A edição aberta do fabricante: código e SDK e versões. |
Trocar de firmware não torna os projetos e samples de um firmware legíveis por outro: guarde os backups feitos sob o firmware oficial para restaurá-los sob ele.
02Modo seguro
Para um firmware que não liga. Um firmware construído sobre o fm1-base que falha duas vezes seguidas ao ligar faz a unidade entrar em SAFE MODE (modo seguro): não há som, mas a USB funciona, então um instalador web ainda alcança a unidade.
- Desligue e ligue a unidade de novo; depois de duas partidas falhas ela mostra o modo seguro.
- Aperte PLAY para tentar ligar o firmware de novo.
- Ou conecte-a e, pelo instalador, instale o firmware de novo ou devolva o firmware oficial.
Se o próprio modo seguro falhar duas vezes, a unidade cai no modo de atualização do próprio chip (04).
03O menu de recuperação do bootloader
Onde houver. O instalador do fm1-base também pode instalar o m-bootloader (MIT), um pequeno bootloader com menu de recuperação. Numa unidade que o tenha, segure PLAY enquanto liga a unidade para abrir o menu; dali um pacote de firmware pode ser instalado por MIDI mesmo quando o firmware não liga. Segure REC enquanto liga para pôr a unidade em modo de atualização, que o instalador alcança.
04O modo de atualização do chip
Para uma unidade presa num laço de travamento, sem o m-bootloader. Segurar REC ao ligar inicia então o modo de
atualização do próprio chip, que um instalador comum não alcança. O script de resgate do felucca-bsp
(tools/fm1_rescue.sh, macOS e Linux, MPL-2.0) devolve o firmware oficial por esse modo, sem hardware extra:
ele confere os arquivos do firmware oficial pelos seus hashes conhecidos e grava só esses. Siga as instruções do próprio
script.
05Uma unidade que não mostra nada
Para uma unidade com a tela apagada que nem aparece na USB. O m-unbricker (MIT) a recupera com uma segunda unidade, funcionando, e um cabo USB-C. Em linhas gerais; a página passo a passo dele dá os detalhes:
- Tenha uma segunda unidade que funcione e que o m-unbricker aceite. Nada é instalado nela: o programa de recuperação roda na memória dela, e o firmware e as configurações dela continuam.
- Abra a página passo a passo no Chrome ou no Edge, num computador, conecte a unidade que funciona pela USB e permita o acesso MIDI quando o navegador pedir. A página inicia o programa de recuperação na unidade que funciona.
- A tela da unidade que funciona passa a guiar você: leve o cabo USB-C para a unidade travada e ligue-a. A unidade que funciona põe o chip da travada no modo de download e a conserta, seja o que for que haja na memória dela.
- Depois instale o firmware oficial (01), se ele ainda não tiver voltado, e restaure o backup.
06Créditos
O m-unbricker e o m-bootloader são de Julius Vitkauskas (MIT). O fm1-base é de Charles Vestal e colaboradores (MPL-2.0), construído sobre o felucca-bsp de Leo Kuroshita, Hügelton Instruments (MPL-2.0); o script de resgate é de Charles Vestal, no felucca-bsp. O firmware oficial, o workbench e o FM1 Open são da M-VAVE. Nenhum deles fez, revisou ou endossa o FAÍSCA. Cada passo desta página é por sua conta e risco: veja a página legal.