Emulator 22 Nov 2026 · Device firmware not releasedEmulador 22 nov 2026 · Firmware do aparelho não lançado
FAÍSCABY RUÍDOPOR RUÍDO
PlayTocar

FAÍSCA / NOISEBOX FOR THE FM-1

Four loops
that sing.

A free, open firmware that turns the FM-1 into a noisebox: four feedback loops joined by a send matrix, a fixed chain of twelve effects inside every loop, played with the hands. There is no oscillator: every sound is the network held at the edge where it starts to ring.

The emulator runs the firmware's own C core. No FM-1 needed.
Keyboard, touch or a MIDI controller.

01 — The instrument, live240 × 240
The core's own screen, drawn as the unit draws itPower, then a white pad
FOUR LOOPSTWELVE EFFECTSNO OSCILLATORMIDIGPL-3.0

02 — Start here

Play.
Learn. Install.

Three steps, all in the browser. Try it before touching your unit.

01 / Play

In the browser.

The emulator is the firmware's core compiled to WebAssembly. Computer keyboard, touch, or a MIDI controller with its own panel for ports, channel and MIDI learn.

Open the emulator
02 / Learn

Five rules, one map.

Five rules cover the whole instrument. The manual's map shows what every control does alone, held and in combination; the cheat sheet fits on one page.

Read the manual Cheat sheet
03 / Install

Not released yet.

The device firmware is being built and tested in stages, each one checked on the hardware before the next. Nothing is offered to install until it is finished. Read the risks and the ways back first.

Status and risks

You need a recent browser to play; Chrome or Edge for MIDI. For the device, when there is a release: Chrome or Edge on a computer, and a USB cable that carries data.

03 — The sound

One chain.
Always the same.

Each of the four loops runs the same fixed chain, in this order, and writes the result into its delay line, which feeds the loop again one period later. The fourth knob of every effect is its MIX; at zero the effect is not in the path.

  1. RETURN + MATRIX + KICK + HISS
  2. DRIVE
  3. BAND · MID FOCUS
  4. FUZZ
  5. BLAST
  6. FOLD
  7. WRAP
  8. RECTIFY
  9. DIVIDE
  10. RING
  11. STARVE
  12. SHIFT
  13. ECHO
  14. PUMP
  15. SWEEP
  16. LOOP DELAY · PITCH SCREAM
  1. LOOPS 1+3 LEFT · 2+4 RIGHT
  2. GATE
  3. DELAY
  4. REVERB
  5. LEVEL
  6. LIMITER

The loops are tuned to partials of MID, from 20 Hz to 10 kHz. GAIN sets how much each loop gives back: below unity the loops ring when struck and fade; above it they sing on their own, and the preamp's saturation holds them there. CROSS scales the 4 × 4 matrix of signed sends between the loops; SCREAM lets the output bend the loops' own delay times. A limiter that cannot be switched off keeps the output at or below −3 dBFS. The theory explains the physics.

EffectKnobsWhat it does
FUZZGAIN TONE BIASTwo saturating stages, the second asymmetric; up to +60 dB.
BLASTGAIN TONE EMPHASISA hard clip from rail to rail, the highs lifted before it.
FOLDDEPTH BIAS SOFTA triangle wavefolder, up to +24 dB into the fold.
WRAPDEPTH BIAS SMOOTHA peak past the edge comes back on the other side.
RECTIFYHALF BIAS TONEFull wave (the octave above) to half wave.
DIVIDEOCTAVE WIDTH TONEFlip-flops: squares one or two octaves below.
RINGCARRIER FREQ DCRing modulation by the neighbour loop or its own sine.
STARVESAG GATE RECOVERA weak supply: the headroom sags, small signals die.
SHIFTHZ SPREAD FEEDBACKA frequency shifter, ±400 Hz.
ECHOTIME FEEDBACK WOWA short echo inside each loop, 2 to 27 ms.
PUMPDEPTH ATTACK RELEASEA compressor inside the loop: it ducks, then swells.
SWEEPRANGE BASE RESOA resonant band-pass moved by the loop's own level.
DELAYTIME FEEDBACK TONEAfter the network: ping-pong, 10 to 120 ms.
REVERBSIZE DAMP WIDTHAfter the network: a small, bright four-line network.

04 — Orientation

Five rules.
One map.

Learn these once and you know the whole instrument. The manual has the map of every control.

  1. 01Three knobs never changeCROSS, SCREAM and GAIN, and LEVEL on the pot.
  2. 02One button, one sectionK1 to K4 play the lit section: LOOP, CHAN, MATRIX, SHAPE, FX, DELAY, REVERB, MOD. CHAN, MATRIX and FX step on when pressed again.
  3. 03Holding is a layerMEMORY and STORE: the sixteen sounds on the white keys. FX: the twelve effects. LFO: the sources, and a turned knob gets a depth. RIBBON: the keys become positions.
  4. 04The fourth knob is MIXIn every effect. At zero the effect is not in the path.
  5. 05The screen says what you touchedName and value, large, for a moment; then the four lamps.

05 — MIDI

The same map
everywhere.

The map lives in the shared core, so the emulator and the firmware read MIDI the same way. Channel: any, or one of 1 to 16. Note-on with velocity 0 counts as note-off.

MessageControl
NOTE 53–79The 27 pads, F3 to G5 (C4 = 60)
NOTE 36–49The 14 buttons: MOTION, RIBBON, LOOP, CHAN, MATRIX, SHAPE, MEMORY, LFO, FX, DELAY, REVERB, MOD, DRONE, STORE
CC 20–23K1–K4, the section in use (absolute)
CC 24 · 25 · 26CROSS · SCREAM · GAIN
CC 7LEVEL, until the pot is moved
CC 120 · 123Releases everything held by MIDI

In the emulator, the MIDI panel under the instrument chooses the input and output ports and the channel, and keeps the bindings made by MIDI learn (Alt-click a control, then move a MIDI control): clear, export and import them as JSON. The output sends the knobs as CC and the lamps as notes on the same map, for controllers that can show them.

06 — What comes next

Roadmap

What is being built and tested now. Dates depend on tests on real units.

Device firmwareBuilt and tested in stages on the hardware: the screen and silence, the controls, the idle engine, the full render.IN PROGRESS
The screenLegibility from a distance, animation, views of the sound: LOOPS, SCOPE, WAVES, MATRIX.IN PROGRESS
Controls on the unitSections and held buttons reviewed for the hands.IN DESIGN
MIDI on the deviceThe emulator's map, over USB and the MIDI input.PLANNED
First releaseAn install page, release notes, exactly what the firmware writes.PLANNED
Emulator and documentsThe emulator with MIDI, sixteen memories, the manual, the theory, this page, in English and Portuguese.DONE

FAÍSCA / CAIXA DE RUÍDO PARA O FM-1

Quatro laços
que cantam.

Um firmware livre e aberto que transforma o FM-1 numa caixa de ruído: quatro laços de realimentação ligados por uma matriz de envios, uma cadeia fixa de doze efeitos dentro de cada laço, tocada com as mãos. Não há oscilador: todo som é a rede mantida na beira em que ela começa a soar.

O emulador roda o próprio núcleo em C do firmware. Não precisa de um FM-1.
Teclado, toque ou um controlador MIDI.

01 — O instrumento, ao vivo240 × 240
A própria tela do núcleo, desenhada como a unidade a desenhaPower, depois um pad branco
QUATRO LAÇOSDOZE EFEITOSSEM OSCILADORMIDIGPL-3.0

02 — Comece aqui

Toque.
Aprenda. Instale.

Três passos, todos no navegador. Experimente antes de mexer na sua unidade.

01 / Tocar

No navegador.

O emulador é o núcleo do firmware compilado para WebAssembly. Teclado do computador, toque ou um controlador MIDI, com um painel próprio para portas, canal e MIDI learn.

Abrir o emulador
02 / Aprender

Cinco regras, um mapa.

Cinco regras cobrem o instrumento inteiro. O mapa do manual mostra o que cada controle faz sozinho, segurado e em combinação; a folha de consulta cabe numa página.

Ler o manual Folha de consulta
03 / Instalar

Ainda não lançado.

O firmware do aparelho está sendo construído e testado por etapas, cada uma conferida no aparelho antes da seguinte. Nada é oferecido para instalar até ele ficar pronto. Leia antes os riscos e os caminhos de volta.

Estado e riscos

Você precisa de um navegador recente para tocar; Chrome ou Edge para MIDI. Para o aparelho, quando houver versão: Chrome ou Edge num computador e um cabo USB que passe dados.

03 — O som

Uma cadeia.
Sempre a mesma.

Cada um dos quatro laços passa pela mesma cadeia fixa, nesta ordem, e grava o resultado na sua linha de atraso, que alimenta o laço de novo um período depois. O quarto knob de todo efeito é o MIX; no zero, o efeito não está no caminho.

  1. RETORNO + MATRIZ + KICK + HISS
  2. DRIVE
  3. BANDA · MID FOCUS
  4. FUZZ
  5. BLAST
  6. FOLD
  7. WRAP
  8. RECTIFY
  9. DIVIDE
  10. RING
  11. STARVE
  12. SHIFT
  13. ECHO
  14. PUMP
  15. SWEEP
  16. ATRASO DO LAÇO · PITCH SCREAM
  1. LAÇOS 1+3 ESQUERDA · 2+4 DIREITA
  2. GATE
  3. DELAY
  4. REVERB
  5. LEVEL
  6. LIMITADOR

Os laços se afinam em parciais do MID, de 20 Hz a 10 kHz. GAIN define quanto cada laço devolve: abaixo da unidade os laços ressoam quando golpeados e somem; acima dela cantam sozinhos, e a saturação do pré os segura ali. CROSS escala a matriz 4 × 4 de envios com sinal entre os laços; SCREAM deixa a saída curvar os tempos de atraso dos próprios laços. Um limitador que não se desliga mantém a saída em −3 dBFS ou abaixo. A teoria explica a física.

EfeitoKnobsO que faz
FUZZGAIN TONE BIASDois estágios de saturação, o segundo assimétrico; até +60 dB.
BLASTGAIN TONE EMPHASISUm corte duro de trilho a trilho, com os agudos realçados antes.
FOLDDEPTH BIAS SOFTUm dobrador de onda triangular, até +24 dB na dobra.
WRAPDEPTH BIAS SMOOTHO pico que passa da borda volta pelo outro lado.
RECTIFYHALF BIAS TONEOnda completa (a oitava acima) até meia onda.
DIVIDEOCTAVE WIDTH TONEFlip-flops: quadradas uma ou duas oitavas abaixo.
RINGCARRIER FREQ DCModulação em anel pelo laço vizinho ou por uma senoide própria.
STARVESAG GATE RECOVERUma fonte fraca: a folga cai, os sinais pequenos morrem.
SHIFTHZ SPREAD FEEDBACKUm deslocador de frequência, ±400 Hz.
ECHOTIME FEEDBACK WOWUm eco curto dentro de cada laço, de 2 a 27 ms.
PUMPDEPTH ATTACK RELEASEUm compressor dentro do laço: abaixa e volta a crescer.
SWEEPRANGE BASE RESOUm passa-banda ressonante movido pelo nível do laço.
DELAYTIME FEEDBACK TONEDepois da rede: pingue-pongue, de 10 a 120 ms.
REVERBSIZE DAMP WIDTHDepois da rede: uma pequena rede clara de quatro linhas.

04 — Orientação

Cinco regras.
Um mapa.

Aprenda uma vez e você conhece o instrumento inteiro. O manual tem o mapa de cada controle.

  1. 01Três knobs nunca mudamCROSS, SCREAM e GAIN, mais o LEVEL no potenciômetro.
  2. 02Um botão, uma seçãoK1 a K4 tocam a seção acesa: LOOP, CHAN, MATRIX, SHAPE, FX, DELAY, REVERB, MOD. CHAN, MATRIX e FX avançam quando apertados de novo.
  3. 03Segurar é uma camadaMEMORY e STORE: os dezesseis sons nas teclas brancas. FX: os doze efeitos. LFO: as fontes, e um knob girado ganha profundidade. RIBBON: as teclas viram posições.
  4. 04O quarto knob é o MIXEm todo efeito. No zero, o efeito não está no caminho.
  5. 05A tela diz o que você tocouNome e valor, grandes, por um instante; depois as quatro lâmpadas.

05 — MIDI

O mesmo mapa
em todo lugar.

O mapa mora no núcleo comum, então o emulador e o firmware leem MIDI do mesmo jeito. Canal: qualquer um, ou um de 1 a 16. Note-on com velocidade 0 vale como note-off.

MensagemControle
NOTA 53–79Os 27 pads, de F3 a G5 (C4 = 60)
NOTA 36–49Os 14 botões: MOTION, RIBBON, LOOP, CHAN, MATRIX, SHAPE, MEMORY, LFO, FX, DELAY, REVERB, MOD, DRONE, STORE
CC 20–23K1–K4, da seção em uso (absoluto)
CC 24 · 25 · 26CROSS · SCREAM · GAIN
CC 7LEVEL, até o potenciômetro ser mexido
CC 120 · 123Solta tudo o que o MIDI segura

No emulador, o painel MIDI embaixo do instrumento escolhe as portas de entrada e saída e o canal, e guarda os vínculos feitos pelo MIDI learn (Alt+clique num controle, depois mexa num controle MIDI): limpe, exporte e importe em JSON. A saída manda os knobs como CC e as luzes como notas, no mesmo mapa, para controladores que sabem mostrá-las.

06 — O que vem aí

Roteiro

O que está sendo construído e testado agora. As datas dependem dos testes em unidades reais.

Firmware do aparelhoConstruído e testado por etapas no aparelho: a tela e o silêncio, os controles, o motor parado, o render completo.EM ANDAMENTO
A telaLegibilidade de longe, animação, vistas do som: LOOPS, SCOPE, WAVES, MATRIX.EM ANDAMENTO
Os controles na unidadeSeções e botões de segurar revistos para as mãos.EM DESENHO
MIDI no aparelhoO mapa do emulador, pela USB e pela entrada MIDI.PLANEJADO
Primeira versãoUma página de instalação, notas da versão, exatamente o que o firmware grava.PLANEJADO
Emulador e documentosO emulador com MIDI, dezesseis memórias, o manual, a teoria, esta página, em inglês e português.FEITO

07 — The device07 — O aparelho

FAÍSCA NOT RELEASEDNÃO LANÇADO

DISCLAIMERAVISO

FAÍSCA is unofficial firmware, not made, reviewed or supported by the maker of the FM-1. Installing it replaces the unit's firmware and can leave the unit unable to start. You flash it entirely at your own risk. The software is provided without warranty of any kind (GNU General Public License, sections 15 and 16). Back up everything first, and do not install it on a unit you cannot afford to have out of service while it is recovered. There is no release to install yet; the firmware's base platform may still change, so the exact steps will be published with the first release.

O FAÍSCA é um firmware não oficial, que não foi feito, revisado nem tem suporte do fabricante do FM-1. Instalá-lo substitui o firmware da unidade e pode deixá-la sem ligar. A gravação é feita inteiramente por sua conta e risco. O software vem sem garantia de nenhum tipo (Licença Pública Geral GNU, seções 15 e 16). Faça backup de tudo antes e não o instale numa unidade que não possa ficar parada enquanto é recuperada. Ainda não há versão para instalar; a plataforma do firmware ainda pode mudar, então os passos exatos sairão com a primeira versão.

01 / The ways back01 / Os caminhos de volta

Recovery.

Recuperação.

From the mildest to the strongest: the official firmware through the official workbench, the platform's safe mode, the bootloader's recovery menu, and, for a unit that shows nothing, a second unit as helper.

Do mais leve ao mais forte: o firmware oficial pelo workbench oficial, o modo seguro da plataforma, o menu de recuperação do bootloader e, para uma unidade que não mostra nada, uma segunda unidade como auxiliar.

The recovery pageA página de recuperação ↗

02 / The terms02 / Os termos

Legal.

Legal.

The licences, the absence of warranty in plain words, what an unofficial firmware means, the trademarks, and privacy: no analytics, no cookies, nothing leaves the browser.

As licenças, a ausência de garantia em palavras simples, o que quer dizer um firmware não oficial, as marcas e a privacidade: sem análise de uso, sem cookies, nada sai do navegador.

The legal pageA página legal ↗

Before installing

Can I go back to the official firmware?

Yes, with the official workbench. The recovery page has every way back, from the mildest to the strongest.

Which browser do I need?

The emulator plays in any recent browser; its MIDI needs Chrome or Edge. Installing on the device needs Chrome or Edge on a computer (Web MIDI and WebUSB), not a phone.

Will I lose my sounds and projects?

Back them up with the official workbench before installing anything. Each release will say exactly which part of the unit's memory FAÍSCA writes and what it leaves untouched.

The installer does not find my unit.

Use a USB cable that carries data, connect the unit directly (not through a hub), switch it on, close other pages or programs that use MIDI, and allow MIDI access when the browser asks.

Do I need an FM-1 to try it?

No. The emulator is the same core and plays in the browser.

Antes de instalar

Posso voltar ao firmware oficial?

Sim, pelo workbench oficial. A página de recuperação tem todos os caminhos de volta, do mais leve ao mais forte.

Qual navegador eu preciso?

O emulador toca em qualquer navegador recente; o MIDI dele pede Chrome ou Edge. Instalar no aparelho pede Chrome ou Edge num computador (Web MIDI e WebUSB), não no celular.

Vou perder meus sons e projetos?

Faça o backup pelo workbench oficial antes de instalar qualquer coisa. Cada versão dirá exatamente que parte da memória da unidade o FAÍSCA grava e o que deixa intacto.

O instalador não encontra a minha unidade.

Use um cabo USB que passe dados, ligue a unidade direto (sem hub), deixe-a ligada, feche outras páginas ou programas que usem MIDI e permita o acesso MIDI quando o navegador pedir.

Preciso de um FM-1 para experimentar?

Não. O emulador é o mesmo núcleo e toca no navegador.

08 — Free software08 — Software livre

Open code.
Open licences.

Código aberto.
Licenças abertas.

The core is portable C11 with no library and no allocation; the emulator is that core compiled to WebAssembly, the firmware places the same core inside the unit's own platform. FAÍSCA is free software under the GNU General Public License, version 3 (GPL-3.0-only). The firmware is built on the FM-1's open application and links the unit's binary SDK under that application's linking exception; every firmware distribution carries the license, the exception and the notices of each component it contains.

Design, sound and direction: Mario Baril. Built on the open application and SDK the FM-1's maker publishes. Recovery: m-unbricker. Type: Barlow Condensed, DM Sans and IBM Plex Mono, under the SIL Open Font License.

O núcleo é C11 portátil, sem biblioteca e sem alocação; o emulador é esse núcleo compilado para WebAssembly, o firmware põe o mesmo núcleo dentro da plataforma da própria unidade. O FAÍSCA é software livre sob a Licença Pública Geral GNU, versão 3 (GPL-3.0-only). O firmware é construído sobre a aplicação aberta do FM-1 e liga o SDK binário da unidade sob a exceção de ligação dessa aplicação; toda distribuição do firmware leva a licença, a exceção e os avisos de cada componente que contém.

Desenho, som e direção: Mario Baril. Construído sobre a aplicação aberta e o SDK que o fabricante do FM-1 publica. Recuperação: m-unbricker. Tipos: Barlow Condensed, DM Sans e IBM Plex Mono, sob a SIL Open Font License.

09 — History09 — Histórico

Changelog

Mudanças